LED Display Thermometer K-type Thermocouple Controller High Temperature Tester For Sale

LED Display Thermometer K-type Thermocouple Controller High Temperature Tester


This item has been shown 12 times.

Buy Now

LED Display Thermometer K-type Thermocouple Controller High Temperature Tester:
$10

LED Display Thermometer K-type Thermocouple Controller High Temperature Tester 1.Description: It is a K-type Thermocouple Controller that sensing the ambient temperature with a K-type thermocouple and displaying it on the display in Celsius. 2.Features: 1>.Use industrial grade K-Type sensor 2>.LED display 3>.Measuring temperature range is wide 4>.High precision detection 5>.Display in Celsius 6>.Programmable work mode 3.Parameters: 1>.Product name: K-type Thermocouple Controller 2>.Work voltage:DC 5V 3>.Temperature type:Celsius 4>.Measure range:-60C~500C 5>.LED Display:Red/Blue 3Bit 6>.Length of sensor:0.4meter 7>.Load voltage:DC 1V-14V or AC 1V-125V 8>.Load current:10A(Max) 9>.Refresh rate:0.5s 10>.Output type:Relay output(It can not output voltage!) 11>.Measurement accuracy:1C 12>.Size for display:79*43*26mm 4.Button/Display Introduction: 1>.Long press means need keep press for more than 3second. 2>.SET:Short press to add 50Celsius for the Set Temperature Value and select set parameter in parameter set mode.Long press enter into parameter set mode. 3>.UP:Short press button to increase parameter value in minimum unit.Long press button to increase parameter value continuously. 4>.DOWN:Short press button to decrease parameter value in minimum unit.Long press button to decrease parameter value continuously. 5>.Restart:Reset. 6>.PV:Display current Actual Temperature Value. 7>.SV:Display the Set Temperature Value. 8>.OUT:Output indicator. 9>.Keep press button UP and DOWN more than 5 second at the same time to restore factory settings. 10>.Automatically save parameters after 5 second. 5.Set Temperature Value: 1>.The Set Temperature Value is parameter temperature. 2>.Short press SET to set an approximate temperature value and then press button UP or DOWN to set precise temperature value. 6.Set Parameter: 1>.Long press SET enter into parameter set mode. 2>.Short press SET to switch select parameter. 3>.Press button UP and DOWN to set parameter value. 4>.P00:Set Working Mode.Heating Mode H and Cooling Mode C.The default mode is H. 5>.P01:Set Return Temperature Value.The set range is 0C-50C.The default value is 2C.That is to set range for Set Temperature Value.If set the Set Temperature Value is 25celsius and the Return temperature is 0.5celsius.So the temperature range is 24.5~25.5celsius. Start heating mode if the current test temperature is lower 24.5celsius.Start cooling mode if the current test temperature is higher 25.5celsius. 6>.P02:Temperature Correction.The set range is -10C to +10C and the default value is 0C.This function can be used when the measured value and the actual value are biased.Corrected value = measured value + set value. If the current measured temperature is 25.8 degrees Celsius and the correction value is -0.2 degree, the actual value shown after the return is 25.8-0.2, which is 25.6 degrees Celsius. 7>.P03:Set Upper Temperature Limit Value.The default value is 500C.Screen will flashing '---' when the test temperature is more than Upper Temperature Limit Value. 8>.P04:Set Lower Temperature Limit Value.The default value is -60C.Screen will flashing '---' when the test temperature is less than Lower Temperature Limit Value. 9>.P05:Lock Parameter.User can not change parameter if turn ON this set parameter. 10>.Heating Mode:Module will output if the Actual Temperature Value is less than Set Temperature Value - Return Temperature Value.Heating equipment starts working and raises ambient temperature if module connect a heating equipment. 11>.Cooling Mode:Module will output if the Actual Temperature Value is more than Set Temperature Value + Return Temperature Value.Cooling equipment starts working and raises ambient temperature if module connect a cooling equipment. 7.Use steps: 1>.Connect sensor to module in right terminal. 2>.Set parameter as following use manual. 3>.Connect to power supply.Pay attention to the connect direction. 8.Application: 1>.Industrial temperature measurement. 2>.Measurement of temperature in the life. 3>.It can be embedded in an instrument to measure certain specific temperatures. 4>.Applied to the measurement of boilers, air, liquids, etc. 5>.Production workshop. 6>.Vegetable cultivation. 9.Note: 1>.Sensor wire should not be connected incorrectly. 2>.Power wire attention direction. 3>.It is a relay output.It can not output voltage.User need provide voltage for load. 10.Package: 1>.1pcs K-type Thermocouple Controller; 2>.1pcs K-Type Thermocouple ;

Powered by WordPress. Designed by WooThemes

Skip to toolbar Log Out