2Pcs NE555 Duty Cycle Pulse Frequency Adjustable Square Wave Generator Module 2X For Sale
2Pcs NE555 Duty Cycle Pulse Frequency Adjustable Square Wave Generator Module 2X:
$6.89
Electronics for IoT, Prototyping & DIY
- ALL ITEMS ·
- MICROCONTROLLERS ·
- POWER ·
- MOTOR CONTROL ·
- SENSORS ·
- AUDIO ·
- COMPONENTS
2Pcs NE555 Duty Cycle Pulse Frequency Adjustable Square Wave Generator Module 2X
2 Pieces NE555 Duty Cycle and Frequency Adjustable Pulse Square Wave Signal GeneratorBoard Module
This NE555 square wave pulse generator module can be used to produce square wave signals for experimental development, or in applications such as driving stepper motors, and as an adjustable pulse for microcontroller (MCU) applications.Only 31mm x 22mm (1.2″ x 0.9″), the board features an NE555 timer chip with jumpers and a potentiometer to fine-tune the frequency in four frequency ranges, and a second potentiometer to adjust the duty cycle (the relationship of how long the output is driven HIGH versus driven LOW). For example, a 50% duty cycle means the output is high 1/2 the time, and low 1/2 the time.Input voltage to the module (VCC) is variable from 5V to 15V DC and draws approximately 15mA at 5v (35mA at 12v) with an output amplitude of 4.2V peak-to-peak to 11.4V peak-to-peak based on the supply voltage.An indicator LED illuminates on a low-level output and flashes relative to the output frequency. At higher frequencies, the LED will appear to be on solid and without a visible flash since the flashing is too fast to see..
NE555 Module Features & Operation:
- Size: 31mm * 22mm(1.2″ x 0.9″)
- Main chip: NE555
- Input Voltage (VCC): 5V-15VDC
- Input current:~100MA
- Output amplitude: 4.2V V-PP to 11.4V V-PP. (Varies with VCC voltage)
- Maximum output current: 15MA (VCC=5V, V-PP greater than 50%), 35MA (VCC=12V, V-PP greater than 50%).
- Output LED indicator (low level, LED is on, high level, LED is off; LED flashes with frequency. When the frequency is higher than about 30Hz, the LED will appear to be always on since the blinking is too fast to see.
- There is a 4-row x 2-pin header that provides jumper settings to select different frequency ranges. The jumper connects different value capacitors in the circuit to change the RC time constant of the circuit. The multi-turn potentiometer near the frequency range jumper provides fine control over the frequency once the range is set.
- Jumper settings are:
- ~1Hz ~ 40Hz
- ~40Hz ~ 500Hz
- ~500Hz ~ 40kHz
- 40kHz ~ >200kHz
- The jumper ranges will vary between modules depending on the tolerances of the components used.
- The output duty cycle can fine-tuned using the onboard potentiometers. Duty cycle and frequency are not separately adjustable; adjusting the duty cycle will change the a square wave signal generator for experimental development
- Used to drive a stepper motor for generating a square wave drive signal
- Generate adjustable pulses for microcontrollers (MCU)
Get it faster! Stocks and ships from our US Colorado office for quick delivery.
We provide FREE USPS First Class Shipping with Tracking - Not Economy Shipping
Featured Products
NE555 Duty Cycle Frequency Adjustable Square Wave Signal Generator Board Module
$5.89YX5300 UART TTL Serial Control MP3 Music Player Module Supports MP3/WAV SD/SDHC
$7.392Pcs SMA Male to SMA Male Plug Series RF Coaxial Adapter Connector 2X US Stock
$6.492 PCS TEC1-12706 12V 60W Thermoelectric Cooler TEC Peltier Plate Module 2X US
$9.894 Pc UHF Male PL259 & Female SO239 to SMA Male & Female RF Connector Adapter Kit
$12.4912V (8-23V) In To 3.3V Out 3A 10W DC-DC Waterproof Converter Module
$6.89300 pcs 3mm 5mm LED Light Kit White Yellow Red Green Blue Assortment with Case
$7.8920mA LED Driver Constant Current Source Regulator - 1/2/5/10 Drivers
$5.29 Add suggested items to your listings - Check it out on 3Dsellers.com· All Rights Reserved to My Store ·
listing template by 3Dsellers.com - Try for Free!
Fatal error: Call to undefined function MagicParser_parse() in /home/leenooks/public_html/store/relateditems.php on line 73